Description

Water based fluororesin non-stick coating PF-600 is designed with two-layer coating system. Thanks to its high density, good inadhesion, easy-to-clean performance and strong practicability. It is applicable for substrates like aluminum, alloy and stainless steel etc. 

Type

Water based fluororesin

Key features

-Eco-friendly

-Excellent heat resistant

-Excellent chemical resistance and abrasive resistance

-Excellent and lasting non-stick performance, easy to clean

Typical properties

Appearance:                                   Black liquid (Primer and top)

Solid content (%):                           35±1

Viscosity (cp):                                  600~1000 Primer

                                                        400~800 Top

Density (g/ml):                                 1.20 Primer/1.30 Top

pH:                                                   8-11 (Primer and top)

Color of the film surface:                  Black with metallic (Flat and smooth)

Curing temperature (℃):                  380-420

Gloss (60° glossimeter):                  10-20

Film thickness (μm):                         20-30

Non-stick performance:                    >10 cycles (Fry eggs at 170±10℃)

Corrosion resistance:                       No blister (Boling 10% salt water for 24 hours)

Abrasion resistance 3KG/21cm2:     >3000 cycles

Hardness (ZHONGHUA pencil):         >H

Application

-Aluminum, die-cast aluminum, alloy and stainless steel

-Frying pan, stock pot, baking tray, electric fry pan and inner pot of electric cooker etc.

Storage and handling

-Available in 20 kg/ barrel or 30 kg/ barrel 

-Store products in tightly closed original containers at 5-40℃

-Shelf life: 9 months from delivery date

-According to non-dangerous goods transport

HOW TO USE

1. Requirement on pre-treatment

-Firstly, apply high-temperature degreasing, then wash with 1%~3% NaOH solution (60℃) for more than 6 minutes, dry it after water rinsing;

-Blast with 80#~120# corundum to make the surface roughness reach 2.0μ~3.0μ, pay attention to sandblast evenly;

-Wash with 1%~3% NaOH solution(60℃) for more than 6 minutes, rinse with water;

-Wash with 1%~3% hydrochloric acid solution (60℃) for more than 6 minutes, rinse with water and dry.

2. Preparation of the coating

-Dispersion of coating: the coating must be fully dispersed before operation;

-Viscosity adjustment: the viscosity could be adjusted according to different spray methods. Dilute with clean water if the viscosity is over high;

-Coating filtration: filtrate the coating with screen (100mesh) before using.

3. Application

-The spraying environment should be dry, well-ventilated, no smoking and fire. We suggest using dedicated spray gun, elevated tank and curing oven;

-The air compressor should be degreased, dewatered and equipped with water oil separator before using;

-Roll the coating at 30rpm speed before using to make sure there is no sediment, and filter with 100 mesh screen;

-Adjust atomization and oil pump capacity of the spraying gun; make sure the unit is clean and flat;

-Preheat the substrate to 35℃ and spray the primer. Dry it at temperature of 120℃~150℃ for 10min-15min. Keep the thickness of primer within 12μm-18μm;

-Spray top coating after the primer is dry and cooling to room temperature, then spray the top. Dry the unit at the temperature of 100℃~150℃ for 10~20 min, and gradually increase the temperature to 380℃~420℃. Keep for 10 min. Keep the thickness of top coat within 10μm~12μm. The thickness of two coat tally should be between 20μm~30μm;

-The oven (or the tunnel drier) must be well ventilated; otherwise, it will lead to color change of coating.

Non-stick Coating Type

↓ ↓ ↓ Please click product model for more informations