SMa-818B5-PLUS 2G/3G/4G/5G Signal Jammer Network Remote Control
Application
2g 3g 4g 5g signal jammer is applied in the Justice Sector(Prisons, detention centers, labor camp, police, courts, procuratorate);the Education Industry(School examination room, classrooms, dormitories, various social test sites, education and training institutions); Government agencies, administrative institutions meeting rooms; Factories and enterprises warehouses, workshops, production lines; Forces and confidential units, theaters, concert halls, memorial halls ,etc.
Technical Parameter
A:Way of communication and networking: remote-controlled by TCP/IP protocols with standard RJ45 network interface
B:Jamming range: Radius: 10~60m (-75dBm, depending on the distance of base station)
C:Transmission power: The whole set: 30W at maximum, each channel 2~3W
D:Jammed signal type: (Notes:List common formats only)
5GNR:n41/n77/n78/n79
TDD-LTE: B34/B38/B39/B40/B41;
TD-SCDMA: B34/B39;
FDD-LTE: B1/B2/B3/B4/B5/B6/B7/B8/B9/B12/B17/B18/B19/B20/B26;
CDMA: BC0;
UMTS(WCDMA)/HSPA+/DC-HSDPA:B1/B2/B4/B5/B6/B8/B19;
GSM: B2/B3/B5/B8;
Data Service:
5GNR/TD-LTE/FDD-LTE/WCDMA/HSPA+/DC-HSDPA
/EVD0/CDMA1X/EDGE/GPRS/VoLTE/
ViLTE/WiFi2.4G/WiFi5.8G
Features
Intelligent networking through TCP/IP when connecting with network cable with independent IP address;
Remote-controlled by main control software, to realize point/grouping/full controlled on/off ;
Fault alarm and query, timing switch with schedule setting freedom;
Remote on/off or adjusting transmission power of any channel of any jammers;
Eight modules work independently, RF power of each channel is 2~3W;
Effectively jamming Mobile, Unicom and Telecom all 2G/3G/4G/5G signals;
Industrial switch power supply, with precision voltage regulator circuit, to ensure the normal work of the host;
Fully sealed protective casing design, waterproof, dustproof, prevent from sabotage and other questions in special application field;
Cooling base with ventilation pipe design, adjusted speed of cooling fans ;
Stable performance, long service life, harmless to human body;
Main Parts
Detailed Technical Parameter
Frequency parameters can be customized. Typical frequencies are shown below
Band Parameter
Channel
Frequency
Average output power
CDMA
865-885MHz
≤4W
GSM
925-960MHz
≤4W
DCS/
FDD
1805-1880MHz
≤2.5W
TDD-LTE
1880-1920MHz
≤2.5W
TD-SCDMA
2010-2025MHz
≤2.5W
WCDMA
2110-2170MHz
≤2.5W
WIFI2.4G
2300-2500MHz
≤2.5W
5G
NR N41
2515-2675MHz
≤2.5W
5G
NR N78
3400-3500MHz
≤2.5W
5G
NR N78
3500-3600MHz
≤2.5W
5G
NR N79
4800-4900MHz
≤2.5W
WIFI5.8G
5725-5850MHz
≤2.5W
Size
410x342x106
Total weight
4.8Kg
Ambient temperature
-40-55℃
Relative humidity
35-85%
Power consumption
160W
Power input
AC
100V-240V
Power output
DC:5V/40A
Installation height
1.8m-2.5m
Installation mode
indoor/outdoor
Enclosure material
plastic molding injection
Part name
Considerations
Jamming range is closely related to the signal strength in the field and may be affected by the system of mobile phone;
Factors that affect jamming range include but not limited to: distance of base station, ip jammer’s orientation, obstacles, wall’s material quality, jammer’s installation height and mode, etc;
Strictly factory test, like aging test. When client receives the machine, please check whether there are something wrong with our device in transit, such as parts fall off , and contact with dealer or manufacturer, for repairing timely;
Installation height is recommended to be 1.8 to 2.5 meters. Install in areas with no obstructions between the target positions. Antenna must be vertical, or antenna is vertical upright on the desktop after breaking off 90 degree, make sure no AC power lines or other audio and video line around antenna in range of 0.2 meters;
In order to avoid possible interference with some electronic devices during use, keep the following common device away from 1 to 2 meters: audio, wireless microphones, radios, computers, TV, Wi-Fi routers, etc.;
The Mothrboard Design
The RF channel modular and each channel work individually
All the motherboard components are used SMT technology
All components are new and original
Advantages
1、Exclusive power amplifier heat sink, large heat dissipation base design
326x93x40mm large heat dissipation base,Fast absorption and emission of heat from power amplifier and power board
The natural wind (cold wind) goes up along the fin gap, bringing out the heat on the cooling teeth quickly and going up
A total of 4 ultra quiet cooling fans (almost no wind noise, adjustable speed) on both sides of the upper end discharge the hot air
2、Cold and hot air lower in and up out, waterproof and damage proof shell
3、The upgrade space is sufficient and can be expanded to 24 channels at most
Meet the upgrading needs of 6G or even 7G in the future;
Reserve the expansion space of dual radiator, dual 12 channel module (24 channels in total) and dual power supply;
Function upgrading, expansion, original parts are all reserved and never wasted.
OEM Customized Service
Frequency spreading can be done for Wi-Fi, Bluetooth, Intercom and wireless data transmit etc.
More than 50 units can provide screen printing OEM service.
Provide neutral device.
Jamming&Monitoring System Software
Intelligent networking through TCP/IP protocols, with built-in independent IP address;
Unified centralized control multiple units across city through remote networking;
B/S framework server platform, providing browser login management;
Timing on/off jammers, the schedule can be set freedom;
Controlled by point to point or grouping control;
Real time monitoring work status of jammers;
Optionally remote on/off each channel of jammers;
Remote adjust transmission power of each channel of jammers;
Fault query and alarm of jammers;
Real time monitoring of jammer working state
TCP/IP Network Mobile Signal Jamming System Connection Topology
TCP/IP Network Jamming System Installation Application Diagram
TCP/IP Jamming System Networking Across City Topology
Engineering Application
In engineering application, the four corners behind the main engine are reserved with bolt holes for wall mounting, which can be directly mounted on the wall:
The installation bolt holes on the back of the equipment can be installed with concealed hanging pieces (thickness 4mm), so as to keep the gap between the equipment and the wall and ventilate;
Silent fans on both sides of device, strengthened to cool the host and power supply
Built-in antenna protect it from personnel sabotage
Internal power supply protect it from sabotage and malicious power off
Waterproof design, available installation both inside and outside
Field Application