The product of UV Spot Light Source can set the time, luminance (adjust irradiation power). A body with 1-4 irradiation Head. More than a dozen of different lenses are available for heads. You can control the heads by either using the user-friendly panel on the front of the controller or via the digital interface. It additionally offers an RS232 interface, which can be used for connecting external computer or other equipment.

The Size of UV LED Spot Light Source Body Machine

The Size of UV LED Spot Light Source Irradiation Machine

Specification Classification of UV LED Spot Light Source Focus Lens

UV LED Spot Light Source Lens

A variety of sizes of lens, can make UV LED point light source flexible application in various ways to achieve the ideal and satisfactory effect.

DSX-003 φ3    DSX-010 φ10

DSX-004 φ4    DSX-012 φ12

DSX-005 φ5    DSX-015 φ15

DSX-006 φ6    DSX-020 φ20

DSX-007 φ7    DSX-030 φ30

DSX-008 φ8   

2. UV LED Spot Light Source Side View Lens (round irradiation, 90° )

DSX-004S φ4    DSX-010S φ10

DSX-005S φ5    DSX-012S φ12

DSX-006S φ6    DSX-015S φ15

DSX-007S φ7    DSX-008S φ8

3. UV LED Spot Light Source Linear Lens (ellipse irradiation)

DSX-L15 3*15

DSX-L20 5*20

Advantages of UV LED Spot Light Source

1. Independent Control 4 LED Irradiation Head

Respectively control irradiation power and time.

Respectively control each LED irradiation head of irradiation power, irradiation time. In the case of the lamp tube, one is needed for each process. But under UPS81, a control device can set 4 LED irradiation head independently. Therefore, a machine is most satisfied with four progress. Otherwise, according to the accumulated lighting time of the LED light, the time of change is reminded, or the warning of temperature anomaly occurs.

2.  External Communication Control

UV irradiation is controlled by external input signals.

Can realize automatic control on production line.

A parallel signal can be sent using an external device such as a programmable controller to control the UV irradiation time of the LED.

By operating the main body, with 0.1 seconds to set various LED irradiation head of UV irradiation time, according to the signal from the outside and began to illuminate the light, or just within the duration of the signal to UV irradiation, etc., which can realize a variety of control. Under the condition of using UPS81, it still can use RS232C to control the light.

UV irradiation only during setting time. 

The UV irradiation is performed according to the external signal pulse input.

The time required for UV irradiation.

External signal ON (1 second), continuous UV irradiation, stop UV irradiation during OFF.

3. Program Irradiation Function

Restrain hardening deformation, achieve high quality and high precision bonding.

Equipped with program irradiation function, it can control the radiation power and time according to the resin and scleroscope. Significantly reduce the hardening shrinkage, achieve high - quality, high - precision bond. In addition to the simple irradiation of continuous irradiation with a certain power, it can also be set for gradual irradiation and intermittent irradiation. Gradual irradiation refers to the use of a program to change power and irradiate at the same time. Interstitial irradiation refers to irradiation according to certain clearance. Seven 10-step programs can be set in 4 LED lights.

4. Ultra long life of irradiation head, economical and affordable LED mode

Compared with the lamp tube, LED mode has the characteristics of long life. The lamp has a life expectancy of about 3,000 hours, and LED has a life expectancy of about 20,000 hours. And, unlike the normally lighted lamp tube, the LED can be used for UV irradiation only when needed. In the case that the ON/OFF time ratio is 1:4 (process preparation time =5, irradiation time =1), it is equivalent to about 100,000 hours of lamp tube mode, which can significantly reduce the operation cost and maintenance time.

5. Standard Bending Light Head Cable

Considering that the LED light head needs to be installed in a removable position, the UV irradiation is carried out repeatedly, and the standard bending cable is used to connect the cable with LED light head. Even move frequently LED light head, you do not worry will appear like quartz optical fiber fracture, can rotate freely (radius of 33 mm, bending resistance more than 10 million times: according to the criteria for the assessment of the company).

Industry Application of UV LED Spot Lihght Source