East West Dual Tilt Solar Ballast Mounting System for Flat Rooftop

Sales East West Dual Tilt Solar Ballast Mounting System for Flat Rooftop

East West dual tilt solar flat roof mounting system is a exclusive design, it can install more solar panel in the same area, and higher energy production output.


  • Snow Load : 1.4KN/M2
  • Wind Load : 60M/S
  • Standard : AS/NZS 1170
  • Certification : ISO9001/CE/UL
  • Service Life : 25 Years
  • Warranty : 10 Years
  • Material : Aluminum 6005-T5 & SUS 304 Stainless Steel

Product Detail  

East West Dual Tilt Solar Ballast Mounting System for Flat Rooftop

 

Kseng`s East West dual tilt mounting system is a exclusive design, it can install more solar panel in the same area, and higher energy production output.Greater overall system power production under the same roof area.

. Cost Effectiveness, the same module qualities ( modules are quite cheap), East West dual tilt mounted on the flat rooftop can save on cost of energy. As solar system in an East-West solar racking are more packed together, potentially you would be saving some rails on the system. When you are installing a large project, bits and pieces adds up.

. Easier on the roof and Prevent winds blowing over

North-facing panels titled at 30° need heavy concrete ballasts or stronger mounting to prevent winds blowing the modules over, or off the roof. Less air resistance when using a East West system allows it to be installed on less structurally robust roofs and preserves roof loading capacity for other projects in the future.

roof mounting details.png

flat roof mount system.jpg




   Material:     Aluminum 6005-T5 & SUS 304 Stainless Steel
   Application:     Flat Rooftop                                                           
   Standard:     AS/NZS 1170
   Wind Load:     60M/S
  Snow Load:     1.4KN/M2
  Certification:     ISO9001/CE/UL
  Warranty:     10 Years
  Service Life:     25 Years
  Applicable Module:    Framed or Frameless

Causion:

To avoid deadlock of stainless steel fastener, please avoid using electric tools for final tightening. And refer to the safe torque refined for stainless steel in the following forms. And: Do not fasten bolts tightly until each component is adjusted properly.


Bolt Dimension
Safe Torque(N*M)Bolt DimensionSafe Torque(N*M)

M1

0.0193M2.50.356
M1.10.0272M30.634
M1.20.0369M3.50.997
M1.40.0578M41.48
M1.60.0853M4.52.14
M1.80.129M52.98
M20.174M65.07
M2.20.229M78.5
M812.3M1024.4
M1242.5M1467.6



Components:

ballate flat solar.jpgflat solar east west.jpg


Installation Steps:

east-west-solar-mounting_02.jpg

east-west-solar-mounting_04.jpg

  1. According to the panel array drawing, Locate the Pillars. Connect Pillars with M10*20 bolt and Guide Slider. 

  2. Construct triangle with angles and bolt M8*25. 

  3.  Put Ballast Plate on Pillar 22, and fix triangle structure to the Pillar 22 with bolt M10*20.

  4. Put on end clamp and mid clamp, not tightened. 

  5. Ballast with Concrete Block.

  6. 7.8. Install panel, tighten bolt of clamps. 

    solar ballast

Merit:

solar mounting bracket

roof project case.png

flat-roof-solar-ballast.jpg





Leave A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
X

Home

Supplier

Leave a message

Leave a message

If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.