Variable optical attenuators,short as VOA, are used to permit dynamic control of optical power levels in a fiber. It can be applied to adjust power level of signal in the optical communication at the output of light sources, E/O converters and for the linear or dynamic range of power meter. Furthermore, they can the used in optical amplifier systems to balance the gain across the different operating wavelengths.

This is a kind of stainless steel tube mini module PLC Splitter 1:16 with sc/lc/fc/st in 0.9mm cable,the cable length is usually 1-1.5m.Available wavelength is:1260-1650nm.

This is a kind of ABS box PLC Splitter available with 1X4/1X8/1X16/1X32/1X64/1X128,2X4/2X8/2X16/2X32/2X64/2X128,the terminators can be sc/lc/fc/st in 3.0mm or 2.0mm cable,the cable length is usually 1-1.5m.Available wavelength is:1260-1650nm.

Capacity: 2~6kVA DC Voltage: 24/48V Product Introduction: ESI is a powerful all in one solar inverter integrated with multiple functions, including a high-performance true sine wave inverter, a powerful battery charger, a MPPT charge controller, and a high-speed automatic transfer switch.

1000BASE-LH SFP 1310nm 40km DOM LC SMF Transceiver Module is designed for use in 100GBASE Ethernet and 4x28G OTN client interfaces throughput up to 40km over single mode fiber(SMF) using a wavelength of 1310nm via duplex LC connectors. Taking BOX+FPC+PCBA separate design, it has great reliability, airtightness and heat dissipation performance. This transceiver is compliant with IEEE 802.3ba 100GBASE-LR4 and OTU4 4I1-9D1F standard. Digital diagnostics functions are also available via the I2C interface, as specified by the QSFP28 MSA, to allow access to real-time operating parameters. With these features, this easy to install, hot swappable transceiver is suitable to be used in various applications, such as 100G Ethernet, 112G OTN OTU4, telecom, service provider applications and 5G wireless network.

Capacity: 3kVA Battery: lithium battery Feature: Portable

10G SFP+ optical transceiver module, support 10Gb/s and up to 100 km transmission, including: SFP+ SR, SFP+ LR, SFP+ ER, SFP+ ZR, etc. It works in high-speed IDC connection solutions, 5G network front-haul solution, network switch, PTN, OTN and so on.

CWDM MUX DEMUX,Multiplexing up to 18 Channels on Fiber Pair 1% Monitor Port for Signal Analyzing or Troubleshooting Passive, Protocol Transparent for Ethernet, FC, OTN, SONET/SDH, etc. Fully Compatible with All ITU-T 1G/10G/25G CWDM Optics Applied to Metro, Regional CWDM Networks

Fiber optic closures provide a protected area for the spliced sections to live, keeping them away from any hazards. Any of these that come in contact with the wires can lead to damage. Bugs may bite through the protective layers, while moisture can flood the cabling. Even things like vandalism and damage from car accidents can be troublesome. A rugged, hermetically sealed fiber optic splice closure can better protect cables and the sensitive data that runs through them from many of the dangers they face.

Variable in-line optical attenuators,also know as adjustable in-line optical attenuator or short as VOA, are used to permit dynamic control of optical power levels in a fiber. It can be applied to adjust power level of signal in the optical communication at the output of light sources, E/O converters and for the linear or dynamic range of power meter. Furthermore, they can the used in optical amplifier systems to balance the gain across the different operating wavelengths.

The pulling eye can further speed up the installation process compared with filed termination. It saves time during installation of conduits, ducts or risers. In addition, the pulling eye protects the connectors of the trunk cables and prevents the cables from twisting during the installation process. Since the pulling eye is strain relived directly onto the outer jacket.With the pulling eye,the tension strength of the cables can reach up to 245N.

A fiber optic HDMI cable is a cable using optical fiber as the transmission medium,the principle of the cable is to integrate the photoelectric conversion line at the hdmi interface and use the fiber optic as the transmission medium material; during the transmission process, the hdmi optical fiber transmitting end converts the hdmi signal into an optical signal and transmits it to the hdmi fiber optic through the optical fiber medium line receiving end, the receiving end then converts the optical signal into a lossless hdmi signal and outputs it to the display device.

MPO/MTP Fiber Optic Cassette Box is usually the connection of trunk cable and the next MPO/MTP cassette in distribution area of MDA, IDA or HDA data centers. It could be installed 1pc or 2pcs of 0.9mm MPO/MTP-LC harness patch cord 12C inside.

Designed for applications in the data center,networking and telecommunications markets that requires a high speed,reliable cable assembly,this next generation product shares the same mating interface with QSFP+ form factor ,making it backward compatible with existing QSFP ports.QSFP28 can be used with current 10G and 14G applications with substantial signal integrity margin.

Fiber optic closures provide a protected area for the spliced sections to live, keeping them away from any hazards. Any of these that come in contact with the wires can lead to damage. Bugs may bite through the protective layers, while moisture can flood the cabling. Even things like vandalism and damage from car accidents can be troublesome. A rugged, hermetically sealed fiber optic splice closure can better protect cables and the sensitive data that runs through them from many of the dangers they face.

Fiber Adapters (Mating Sleeve Fiber Adapter or Standard Fiber Adapter or Bulkhead Type Fiber Adapter) also called fiber adaptors,are used to link optical cables or device. Usually they are female to female,or female to male. SZOPT’s fiber adapters are mainly with ceramic sleeves, but phosphor bronze sleeve is an option for some special requirement.

The PLC Router Communication Module is equipped with the latest Topscomm power line carrier communication technology, has been widely used in Topscomm smart communication terminals and energy data acquisition terminals.

1000BASE-ZX SFP 1550nm 80km DOM LC SMF Transceiver Module is designed for use in 100GBASE Ethernet and 4x28G OTN client interfaces throughput up to 80km over single mode fiber(SMF) using a wavelength of 1550nm via duplex LC connectors. Taking BOX+FPC+PCBA separate design, it has great reliability, airtightness and heat dissipation performance. This transceiver is compliant with IEEE 802.3ba 100GBASE-LR4 and OTU4 4I1-9D1F standard. Digital diagnostics functions are also available via the I2C interface, as specified by the QSFP28 MSA, to allow access to real-time operating parameters. With these features, this easy to install, hot swappable transceiver is suitable to be used in various applications, such as 100G Ethernet, 112G OTN OTU4, telecom, service provider applications and 5G wireless network.

MPO/MTP Trunk Cable 24/48/72/96/144 Core is type of mulitcore cable assemblies facilitate rapid deployment of high density backbone cabling in data centers and other high fiber environment with at least 2pcs of MPO/MTP connectors, reducing network installation or reconfiguration time and cost.MTP/MPO are used to interconnect cassettes, panels, or fan outs using a compact and rugged microcables structre. The compact cable optimizes cableway use and improve airflow.These MPO/MTP cable are build with the highest quality components , Low loss elite(premium) versions are offered accordingly,please contact SZOPT for details.

Ethernet patch cables are widely used for lan network,available cat5,cat5e,cat6,cat6a,cat7,cat7a,cat8,etc,with UTP,STP/FTP,SFTP,SSTP etc.shielding mode.Please check with us for details.